TPD1036F 2013-12-26 1 toshiba intelligent power device silicon monolithic power mos integrated circuit TPD1036F 2-in-1 low-side power switch fo r motor, solenoid and lamp drivers the TPD1036F is a 2-in-1 low-side switch. the output has a vertical mosfet, and the input can be directly driven from cmos or ttl logic (e .g., an mpu). the ic provides intelligent protecti on functions. features ? two built-in power ic chips with a structure that incorporates a control block and a vertical power mosfet on each chip. ? can be directly driven from a microprocessor, a cmos logic ic, etc. ? overvoltage (active clamp), overtemperature (thermal shutdown), and overcurrent (current limiter) protecti ons are built in. ? low on-resistance: r ds (on) = 0.5 (max) (@v in = 5 v, i d = 0.7 a, t ch = 25c) ? low drain cut-off current: i dss = 10 a (max) (@v in = 0 v, v ds = 30 v, t ch = 25c) ? low input current: i in = 300 a (max) (@v in = 5 v, t ch = -40 to 110c) ? housed in the 8-pin sop package and supplied in embossed carrier tape. pin assignment (top view) marking note: a line under a lot no. identifies the indication of product labels not underlined: [[pb]]/includes > mcv underlined: [[g]]/rohs compatib le or [[g]]/rohs [[pb]] please contact your toshiba sales r epresentative for details as to environmental matters such as the rohs compatibility of product. the rohs is directive 2011/65/eu of the european parliam ent and of the council of 8 june 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment. this product has a mos structure and is sensitive to electrostatic discharge. weight: 0.08 g (typ.) 1 2 3 4 8 7 6 5 drain1 drain1 drain2 drain2 source1 in1 source2 in2 tpd1036 f lot no. note part no. (or abbreviation code) start of commercial production 1999-10
TPD1036F 2013-12-26 2 block diagram pin description pin no. symbol pin description 1 source1 source pin 1. 2 in1 input pin 1. this pin is connected to a pull-down resistor intern ally, so that even if the input is open-circuited, output never turns on inadvertently. 3 source2 source pin 2. 4 in2 input pin 2. this pin is connected to a pull-down resistor intern ally, so that even if the input is open-circuited, output never turns on inadvertently. 5, 6 drain2 drain pin 2. drain current is limited (by current limiter) if it exceeds 1 a (min) in order to protect the ic. 7, 8 drain1 drain pin 1. drain current is limited (by current limiter) if it exceeds 1 a (min) in order to protect the ic. drain1 in1 overcurrent detection /protection 8 7 overtemperature detection /protection 1 2 source1 drain1 drain2 in2 overcurrent detection /protection 6 5 overtemperature detection /protection 3 4 source2 drain2
TPD1036F 2013-12-26 3 timing chart truth table v in v ds output state operating state l h off h l on normal l h off h h current limiting (limiter) load short-circuited l h off h h off overtemperature input signal overcurrent detection channel temperature drain-source voltage drain current current limiting (limiter) thermal shutdown active clamp normal v dd v (cl)dss overtemperature detection 150c (min) 5c hysteresis (typ.) inductive load drive
TPD1036F 2013-12-26 4 absolute maximum ratings (ta = 25c) characteristics symbol rating unit drain-source voltage dc v ds 30 v drain current i d internally limited a input voltage v in ? 0.3 to 6 v power dissipation (t = 10 s) (note 2) p d 2.0 w single pulse active clam p capability (note 3) e as 23 mj active clamp current i ar 1.5 a repetitive active clamp capability (note 4) e ar 0.2 mj operating temperature t opr ? 40 to 110 c channel temperature t ch 150 c storage temperature t stg ? 55 to 150 c note 1: using continuously under heavy loads (e.g. t he application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operat ing temperature/current/voltage, etc. ) are within the absolute maximum ratings and the operating ranges. please design the appropriate reliability upon reviewing the toshiba semiconductor reliability handbook (?handling precautions?/?derating concept and methods?) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). thermal characteristics characteristics symbol max unit thermal resistance, channel to ambient (note 2) r th (ch-a) 62.5 c/w note 2: mount on glass epoxy boad [25.4 25.4 0.8mm] (with the two devices driving)(t =10 s) note 3: single pulse active clamp capability test condition v dd = 25 v, t ch = 25c (initial), l = 10 mh, i ar = 1.5 a, r g = 25 note 4: repetitive rating: pulse width limited by maximum channel temperature
TPD1036F 2013-12-26 5 electrical characteristics characteristics symbol test circuit test condition min typ. max unit drain-source clamp voltage v (cl) dss ? t ch = -40 to 110 v in = 0 v, i d =1ma 40 ? 60 v t ch = 25 1.0 ? 2.8 input threshold voltage v th ? t ch = -40 to 110 v ds = 13 v, i d = 10ma 0.9 ? 3.0 v t ch = 25 ? 3 ? 6 protective circuit operation input voltage range v in (opr) ? t ch = -40 to 110 ? 3.5 ? 6 v t ch = 25 ? ? 10 drain cut-off current i dss ? t ch = -40 to 110 v in = 0 v, v ds = 30v ? ? 100 a i in (1) ? t ch = -40 to 110 v in = 5 v, at normal operation ? ? 300 input current i in (2) ? t ch = -40 to 110 v in = 5 v, when overcurrent protective circuit is actuated ? ? 350 a t ch = 25 ? 0.3 0.5 drain-source on-resistance r ds (on) ? t ch = -40 to 110 v in = 5 v, i d = 0.7 a ? ? 0.75 overtemperature detection t s ? ? v in = 5 v 150 160 ? c t ch = 25 1.5 2.5 ? overcurrent detection i s 2 t ch = -40 to 110 v in = 5 v 1 ? ? a t ch = 25 ? ? 30 t on t ch = -40 to 110 ? ? 60 t ch = 25 ? ? 60 switching times t off 1 t ch = -40 to 110 v dd = 13 v, v in = 0 v/5 v, i d = 0.7 a ? ? 90 s drain-source diode forward voltage v dsf ? t ch = 25 v in = 0 v, i f = 1.5 a ? ? 1.7 v test circuit 1 switching times measuring circuit test circuit measured waveforms test circuit 2 overcurrent detection measuring circuit test circuit v in waveform v ds waveform 5 v 90% t on 10% 10% 90% t off 13 v TPD1036F in drain source v v dd v in = 5 v i d r l i s i d r l r l decrease 0 a TPD1036F in drain source v v dd = 13 v i d = 0.7 a p.g. 0 v
TPD1036F 2013-12-26 6 channel temperature t ch (c) v (cl) dss ? t ch drain-source clamp voltage v (cl) dss (v) v th ? t ch in p ut threshold volta g e v th ( v ) i in (1) ? t ch i in (2) ? t ch r ds (on) ? t ch r ds (on) ? v in v in = 0 v i d = 1 ma 0 ? 80 20 ? 40 40 160 60 10 0 30 40 120 50 80 v ds = 13 v i d = 10 ma 0 ? 80 2 ? 40 40 160 5 1 0 3 4 120 80 v in = 5 v normal operation 0 ? 80 100 200 ? 40 0 40 80 120 160 300 400 v in = 5 v overcurrent protective circuit is actuated 0 ? 80 100 200 ? 40 0 40 80 120 160 300 400 v in = 5 v i d = 0.7 a 0.0 ? 80 0.4 ? 40 40 160 0.2 0 0.6 0.8 80 120 i d = 0.7 a t ch = 25c 0.0 0 0.4 4 8 0.2 2 0.6 6 0.8 channel temperature t ch (c) channel temperature t ch (c) channel temperature t ch (c) input current i in(1) ( a) input current i in(2) ( a) drain-source on-resistance r ds(on) ( ) drain-source on-resistance r ds(on) ( ) channel temperature t ch (c) input voltage v in (v)
TPD1036F 2013-12-26 7 i s ? t ch i s ? v in t on, t off ? t ch switching times t on , t off ( s) v in = 5 v 0 ? 80 2 40 160 1 ? 40 3 120 4 5 0 80 t ch = 25c 0 0 2 8 1 2 3 4 5 4 6 v dd = 13 v v in = 5 v i d = 0.7 a 0 ? 80 40 160 20 ? 40 40 120 0 80 t off t on 60 p d ? ta overcurrent detection i s (a) channel temperature t ch (c) input voltage v in (v) overcurrent detection i s (a) channel temperature t ch (c) dc mount on glass epoxy boad [25.4 25.4 0.8mm] (with the two devices driving) 0 0 1.0 40 120 200 2.5 0.5 80 1.5 2.0 160 t = 10 s ambient temperature ta (c) power dissipation p d (w)
TPD1036F 2013-12-26 8 package dimensions weight: 0.08 g (typ.)
TPD1036F 2013-12-26 9 restrictions on product use ? toshiba corporation, and its subsidiaries and affiliates (collect ively "toshiba"), reserve the right to make changes to the in formation in this document, and related hardware, software and systems (collectively "product") without notice. ? this document and any information herein may not be reproduc ed without prior written permission from toshiba. even with toshiba's written permission, reproduc tion is permissible only if reproduction is without alteration/omission. ? though toshiba works continually to improve product's quality and reliability, product can malfunction or fail. customers are responsible for complying with safety standards and for prov iding adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a ma lfunction or failure of product could cause loss of human life, b odily injury or damage to property, including data loss or corruption. before customers use the product, create designs including the product, or incorporate the product into their own applications, cu stomers must also refer to and comply with (a) the latest versions of all relevant toshiba information, including without limitation, this document, the specifications, the data sheets and application notes for product and the precautions and condi tions set forth in the "toshiba semiconductor reliability handbook" and (b) the instructions for the application with which the product will be us ed with or for. customers are solely responsible for all aspe cts of their own product design or applications, including but not limited to (a) determining the appropriateness of the use of this product in such design or applications; (b) eval uating and determining the applicability of any info rmation contained in this document, or in c harts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operatin g parameters for such designs and applications. toshiba assumes no liability for customers' product design or applications. ? product is neither intended nor warranted fo r use in equipments or systems that require extraordinarily high levels of quality and/or reliability, and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage and/or serious public impact ( " unintended use " ). except for specific appl ications as expressly stated in this document, unintended use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used f or automobiles, trains, ships and other transportation, traffic si gnaling equipment, equipment used to control combustions or expl osions, safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. if you use product for unintended use, toshiba assumes no liability for product. for details, please contact your toshiba sales representative. ? do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy product, whether in whole or in part. ? product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. ? the information contained herein is pres ented only as guidance for product use. no re sponsibility is assumed by toshiba for an y infringement of patents or any other intellectual property rights of third parties that may result from the use of product. no license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. ? absent a written signed agreement, except as provid ed in the relevant terms and conditions of sale for product, and to the maximum extent allowable by law, toshiba (1) assumes no liability wh atsoever, including without limitation, indirect, co nsequential, special, or incidental damages or loss, including without limitation, loss of profit s, loss of opportunities, business interruption and loss of data, and (2) disclaims any and all express or implied warranties and conditions related to sale, use of product, or information, including warranties or conditions of merchantability, fitness for a particular purpose, accuracy of information, or noninfringement. ? do not use or otherwise make available product or related so ftware or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or m anufacturing of nuclear, chemical , or biological weapons or missi le technology products (mass destruction w eapons). product and related software and technology may be controlled under the applicable export laws and regulations including, without limitat ion, the japanese foreign exchange and foreign trade law and t he u.s. export administration regulations. export and re-export of pr oduct or related software or technology are strictly prohibit ed except in compliance with all appl icable export laws and regulations. ? please contact your toshiba sales representative for details as to environmental matters such as the rohs compatibility of pro duct. please use product in compliance with all applicable laws and regula tions that regulate the inclusion or use of controlled subs tances, including without limitation, the eu rohs directive. toshiba assumes no liability for damages or losses occurring as a result of noncompliance with applicable laws and regulations.
|
